69精品国产人妻国产毛片,欧美一级毛片ⅩXX粉色视频,在线观看免费人成视频无码,欧美白人做受XXXX视频,337p粉嫩日本欧洲亚洲艺术
Hotline:13924627849

Lasted News:

更多

Contact Us

Shenzhen Haolin Pml Precision Mechanism Ltd
Hotline:400-6846-806
Fax:0755-84196969
Tel:13924627849 (Mr.Hou)
Tel:18922863481 (Ms.Lai)
-mail:houlz@szhaolin.com.cn
Add:building 2, Huaguan Industrial Park, No. 63, Zhangqi Road, Guixiang community, Guanlan street, Longhua District, Shenzhen,china

Industry News

You are here:Home >> News >> Industry News
Dispenser operating procedure FAQ
Publish:電子產(chǎn)品全自動柔性組裝線,深圳市豪林精密機(jī)械有限公司  Time:2013-12-25
The most common problem encountered is the dispenser valve problems , to solve the following problem occurs when using plastic valves often an effective way .

One of the common problems process dispenser drip dispensing valve operation
1 After this happens often related to the completion of the dispensing valve .

2.95% of such cases are caused because the caliber of the needle used is too small.

3 small needles will affect the flow of the liquid causes back pressure , resulting in the formation of the phenomenon shortly after the completion of drip dispensing valve closed . The needle is too small will affect exhaust valve begins to bubble gum action when used as long as the replacement of a large needle to solve this problem.

4 backpressure tapered helical needle produces the least liquid flow most smoothly.

5 after the air within the liquid dispensing valve produces complete drip off phenomenon , it is best to preclude liquid air , or use of a bubble-containing gel is not easy . Centrifugation or gel first using the deaeration .

Two sizes of glue dispensing operation process inconsistencies FAQ
1 When the glue is inconsistent mainly for storage of fluid pressure cylinder or air pressure generated by instability .

2 meter inlet pressure regulator should be set at the lowest of low pressure over the factory 10 to 15psi., The pressure should be between the pressure tube using a pressure regulator above the middle of the table , you should avoid using a pressure gauge between being low pressure parts.

3 dispensing valve control pressure should be at least 60psi or more in order to ensure the stability of the plastic .

4 Finally, you should check out the glue time if less than 15 / 1000 seconds will cause the plastic instability . , Glue glue more time to grow more stable .

Three of the flow rate is too slow process of dispensing operations FAQs
1 If the flow rate is too slow pipeline should be from 1/ 4 "to 3/8 ."

2 If there is no need for the pipeline should be as short as possible .
3 In addition to change the tube , but also change the plastic mouth and pressure , so full speed up the flow rate.

Four bubbles within the fluid dispensing process operating FAQ
1 . Excessive fluid pressure if coupled with the valve open time is too short compared with the liquid may penetrate the air . Solutions to reduce the fluid pressure and the use of conical oblique needle .

       
2 V. glue dispensing operation of the process FAQ blocked.

3 such cases is mainly due to excessive moisture or repeated used instant glue . Be sure to use fresh, instant glue . The pipeline does not contain moisture Aceton with acetone thoroughly cleaned . After air drying for use should be determined between the plant and the installation of pneumatic valve system with plastic filter . ( If the above method does not work, you should use nitrogen ) .

Dispensing needle selection method :

1 . Four criteria : a small point - small needles, low- pressure , short-term high point - a large needle , greater pressure , longer concentrated glue - inclined needles, greater pressure , the time needed to set an aqueous liquid - small needles, small pressure needed to set the time .

2 . Fluids require special settings :

( 1 ) instant glue : water-based instant glue safe piston and Teflon -lined metal needles, for the thick of instant glue , use a tapered helical needle , For flexible use PP needle.

(2) UV glue : Use amber syringes, needles white piston and inclined (which can block ultraviolet ) .

( 3 ) light-curing adhesive: use black opaque syringes, white piston , the needle can block ultraviolet .

( 4 ) Anaerobic : Use 10CC syringes and white PE common piston .

( 5 ) and paste sealant fluid : If using white piston rebound serious , please use the security style living style , using oblique needle .
Previous:  2019/10/26
Next:Automatic Screw Machine FAQ  2013/12/25
国产 成年发 精品 | 四川少妇XX谢欧美 | 日韩高清无码不卡猎奇毛片 | 亚洲一区高清无码 | 日本少妇不卡一二 | 中文字幕精品人妻 | 无码A片大屁少妇久久久久 少妇AV射精精品蜜桃专区 | 九色自慰喷白浆9 1糖心 | 性一交一伦一片A片在线观看 | 国产优质视频一区二区三区 | 免费在线观A片网站 | av资源在线播放 | 小黄书AV一区二区三区资源网 | 国产欧买日韩一区二区三区精品 | 派91人妻偷拍 对白派 | 人妻偷人VA精品国产旡码 | 91国产成人在线免费视频 | 少妇久久免费视频 | 亚洲成人在线观看无码 | 精品少妇一区二区三区四区 | 91少妇人妻偷人网站 | 亚洲黄色视频免费观看 | 影音先锋 熟女亚洲制服丝袜 | EEUSS国产一区二区三区JDAV | 蕾丝视频官网在线看 | 黄色视频网站一区二区 | 午夜影院成人无码 | 国产午夜精品一区二区 | 欧日韩不卡免费视频在线 | 久久精品免费一区二区喷喷喷 | 成 人 免费 黄 色 | 国产伦精品一区二区三区视频色欲 | 亚洲色婷婷久久精品AV蜜桃久久 | 亚洲国产成人精品无码一区 | 无码毛片视频一区二区本码浅 | 厨房free性hd猛性BBW厨房 | 无码视频1区,2区,3区 | 成年人视频成年人电影久久精品 | 亚洲无码在线播放 | 亚洲影视成人一本AV | 免费看三级,人妻 |